What is meant by scrogging?
Scrogging & trellising are two processes that spread out and do the setting up of the branches of marijuana plants. They do so by making use of rope, string, or netting. They appear just similar, but there is a major subtle difference:
- Scrogging assists in training marijuana plants for getting higher yields
- Trellising simply gives support to plants
Scrog is an abbreviation for the screen of green. Yet another specified term for scrogging is “sea of green”.
Why to scrog cannabis plants?
Scrogging stretches the branches of marijuana plants into a screen, by doing the creation of an even canopy. Scrogging comes with numerous benefits:
- Light might hit more branches, thus it does the production of higher yields and more buds
- The air might flow through the plants more which assists in reducing pests and mold
- Branches get the structural support. This is the reason that heavy buds don’t weigh down the plants and snap branches
- It makes the working of the plants easier. The reason is that branches are more spread out
All branches that are above the screen, the canopy are going to fill out with thick buds. On the other hand, most of the foliage that is below the screen will get shaded out.
You will have the desire to prune the bottom branches along with the dead leaves. It is about those leaves that are below the screen. The reason is that they either will not do the production of buds. Or these will not do the production of buds that are of poor quality.
The plant might focus its all of energies above the canopy that does the production of high-quality buds up there. It does so by cutting off these lower branches.
When to start scrogging of cannabis plants
If you are staying one step ahead of the plant, scrogging is going to work best for you. Most ideally, you have the desire of setting the screen. So. the branches are going to grow into it in comparison to having to push branches into if after. You have to do monitoring week by week and assist branches through the screen as and when they grow.
If you are in need of setting a screen after the fact and putting branches in it. It is not the end of the world. You just have to be gentle with your plants.
The branches of marijuana must be in a screen after the plants have completed getting topping and before flowering. If you still need to top or cut off branches, plants are going to take a different shape.
The reason is that they should not be on a screen yet. And you would have the desire of setting out of branches in a screen before flowering. The reason is not to disturb plants when they are doing the production of buds.
Other points to remember before you scrog weeds
When you will combine scrogging with topping, it will work best. Topping will assist in keeping branches at a similar length. These will also keep the canopy even because of making light to hit buds sites evenly.
- Height: Set out the screen about 1 ft. above the base of the plants
- Size: It assists in keeping the same strains together as they will come with a similar size and shape. If you have numerous strains, you have to group them by height.
- Spacing: You must always ensure to properly space your plants. The branches of one plant must slightly interlock with the branches of the plants that are next to it. It signifies about 1-2ft. between pots.
A better way of gauging spacing is to do stretching out the longest branch of a plant toward the plant that is next to it. It happens when it reaches the middle of the next plant to which it is close. It should also do overlapping with the longest branch of the adjacent plant by 6″ or so.
Scrogging to marijuana when these are outdoors
When you are growing marijuana outdoors, the easiest way for spreading out branches is to do purchasing of a tomato cage or some other pre-made structure. You can also put it around the plant when it is young. The plant will grow into it and as it does, you can assist branches along by pulling them through different points of the cage.
It might be easier for you to build a frame or set posts around all the plants. It is dependent on how big your marijuana weed plants are or how many you are having.
You can drive T-posts or large wooden stakes into the ground when you are growing outdoors. It is for the formation of a rectangle around your marijuana plants.
After that, you can stretch a screen over the posts. You can slide it down to the level of the plants. Either you can let them grow into the screen or pull the branches through it.
Scrogging of marijuana indoors
Around the plants, you can build a structure or frame when you are growing indoors also. A-frame made out of PVC pipe is a common indoor trellising structure.
You can also affix a set of posts of some kind to any structure that is sufficiently sturdy for supporting a screen. Another setup is to nail some 2*4s which are upright into the tray of a plant.
How to place the branches of marijuana in a scrog
There is an art to scrogging. You have the necessity to put a set of plants together and stretch their branches. It is for making them not grow on top of each other or shade each other out.
Scrogging is inclusive of reading a plant for seeing what it requires. Usually, it is inclusive of some fine-tuning. But, with patience and little time this training technique is going to keep your marijuana plants lush and healthy. Along with this, it serves you with big yields.
There is a very crucial question before putting branches into the scrog. It is, where does the branch have the desire to go? If a branch doesn’t have the desire of staying where you put it. You might require to place it somewhere else. And you should never force it.
The branches in the screen must interlock with the branches of the marijuana plants around it. For instance, hands have folded together.
You should always remember that each branch comes with a different length. And there is no exact measurement for how close or far apart each branch or plant must be.
You should also make efforts for filling each square mesh of the green with a single branch. A person should also avoid putting two branches in one square and he should also not leave a square empty.
It will make sure that each branch will get sufficient light and space. Along with this it also ensures that there is being the utilization of its maximum potential. The lighter each branch is receiving, the bigger buds will get.
